JSzymczyk 0 Report post Posted March 21, 2013 This is the best way, in my opinion, to make a Really Good marabou bugger tail or streamer wing. 1. Select a marabou plume. The one pictured is pretty good quality. 2. Break off the tip section of the stem. On not-so-good plumes, this will be very obvious. 3. Gather the remaining "tip" fibers of the plume and stroke them together into a bunch. Separate out the fibers from further down the stem which end up being too short and just create unnecessary bulk. 4. Switch hands and measure the length of the marabou fibers against your hook and adjust your grip as needed. Keeping the bunch firmly pinched, switch back if needed and tie in. Done. You can use the leftover marabou material for other flies if you want. This method gives you the nicest, most consistent marabou tails compared to stripping bunches of fibers off the plume and tying in. "Strung" marabou is pretty cheap and I've found usually over 90% or so of the plumes are useable if you break out the tip of the stem. Quote Share this post Link to post Share on other sites
tidewaterfly 0 Report post Posted March 21, 2013 Joel, great SBS & information. I usually leave the tips, but am very selective about the plumes I choose, and agree that the strung "Blood Quill" marabou is one of the best ways to go for tying, particularly for buggers. I'll often use what's left over as well, but it does take more time to get the tips even & make it look good. Quote Share this post Link to post Share on other sites
Mattpreat 0 Report post Posted March 21, 2013 Often times I will use the marabou as a tail, then use the remaining as a body. If done right it makes for some good and easy to tie wooly buggers or leeches which work awesome on the stocked trout lakes around here. Quote Share this post Link to post Share on other sites
Kirk Dietrich 0 Report post Posted March 21, 2013 Yep, that's a good way for sure, it makes the stuff much easier to control. Like Tide, I usually leave the tip but not always. Now, on large buggars like for bass and redfish, a really good way is to select the finely stemmed plumes, tie in by the tip of the stem and palmer/wrap the plume around the shank up towards the hook eye. After tying it off, usually goes a quarter inch or a little more, stroke the fibers back to the tail and wrap back to the back with your thread. For a nice mottled effect, do two different colors at the same time so the fibers mix all together. Granted, the tail length is limited by the length of the marabou fibers, which can be pretty long but for big flies its really good and it comes out full and pulses nicely. Sorry I don't have an sbs for that. Kirk Quote Share this post Link to post Share on other sites
KOKOEK9 0 Report post Posted July 2, 2014 thanks for your hints Quote Share this post Link to post Share on other sites
ScottK 0 Report post Posted July 3, 2014 Well crap.... I had most of my flies done for a swap I'm in, and I used this method this morning for one. I was gonna go fishing today because I would have had my flies done but Nooooooooo, now I need to break out the razor blade and redo most of 'em. Thanks for ruining my planned fishing trip..... Seriously, great tip! (For me anyway, my marabou tails look much better this way). Quote Share this post Link to post Share on other sites
Tsuribaka 0 Report post Posted July 4, 2014 I actually just started tying woolly buggers and think I'll try this method out for my marabou. Do any of you rip/tear off the tips of the marabou to get "fluffier" tails? I saw this in this video (1min 55sec) and wondered if others did this regularly. Due to my limited budget, I try to get the most out of my materials and use the feathers on the bottom like this guy (1min 55sec). Someone else linked this video in the past and I just happened to bookmark it. Quote Share this post Link to post Share on other sites
flytire 0 Report post Posted July 4, 2014 i do not pinch marabou to length as i prefer to achieve the correct length at tie in Quote Share this post Link to post Share on other sites