Jump to content
Fly Tying

Jaydub

core_group_3
  • Content Count

    1,216
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Jaydub

  • Rank
    Advanced Member

Previous Fields

  • Favorite Species
    Trout
  • Security
    22

Profile Information

  • Location
    In a van down by the river

Recent Profile Visitors

12,590 profile views
  1. Be sure to clean out all of the fuzz from the hair before attempting to stack it. The large stacker can be used for smaller flies. Hold it at an angle so that the hair stays on one side of the stacker and tap on the edge of the table.
  2. TMC 100 is really a dry fly hook. Of course, you could use it for wet flies, it's just a light wire hook. Daiichi 1560 is a 1xl nymph/wet fly hook. The 1550 is standard length. I use the 1xl for most nymphs. Sticking with TMC and Daiichi (there are a lot of cross reference charts out there): 1. California mosquito: TMC 100, Daiichi 1100 or 1170, 1190(barbless) 2. Soft hackle wet flys: TMC 3761 0r 3769 or Daiichi 1550 or 1560 3. Black gnat: Dry see 1 above. Wet see 2 above. 4. BH Soft hackle: TMC 3761 or Daiichi 1560
  3. I just leave them on the whole feather until I need them.
  4. The original Found Link is not a Hackle Stacker, If that makes it more tempting.
  5. March Brown Wet Fly Hook: Wet fly Tag: Gold tinsel Tail: Pintail flank dyed Wood duck Rib: Gold oval tinsel Body: Hare's mask blend Hackle: Brown Partridge Wings: Mottled Turkey
  6. March Brown Spider Hook: Wet Fly Thread: Red, Danville 6/0 Rib: Gold oval tinsel Body: Hare's mask blend Hackle: Brown Partridge
  7. You guys are knocking it out of the park with Norm's Wet flies and Streamers, and Poopdeck's Hackle Stackers.
  8. Sounds like a real defensive battle.
  9. Properly dismantling a radio tower requires specialized skill, equipment and time. Especially one that old where all of the sections are probably rusted together. My guess is they just removed the guy wires and toppled it over, then cut it up for scrap.
  10. Seems like it would work, but I would look at how well it closes at the handle end. Any gap can cause the clamped materials to be loose.
  11. And yet there will be 65000 willing suckers (I mean participants).
  12. Yes I have some stored that way and some in plastic compartment boxes.
  13. I had to look that up. Not what I expected for a "Midge". LOL
  14. I don't have any plans, but I made dividers for some shallow metal drawers that I have. It's made from 1/8" MDF. The dividers interlock with table saw kerf-width cuts of half the depth. Here is one of the dividers removed to give you the idea. I started by ripping the strips to width. To cut the slots, I used a sacrificial extension attached to the miter gauge. I added a short 1/8" pin to the extension, to set the spacing. I could cut one slot, drop that slot over the pin, cut the next slot, drop that slot over the pin an repeat... I think that I may have clamped several strips together for this operation. It's been a few years.
  15. Green Butt Skunk Hook: TMC 7999 Thread: Black, Danville 6/0 Tag: Silver tinsel TailL Red hackle fibers Butt: Chartreuse yarn Rib: Silver oval tinsel Body: Black Angora Goat dubbing Hackle: Black Wing: White hair, might be skunk or kidd goat. The label is gone.
×
×
  • Create New...