|Fly Pattern Database / Browse by Topics / Browse by Material|
|Fly Pattern Database Home · Search · Upload A Pattern · My Bookmarks · Browse by Material · Browse by Members · Browse by Tags · Members I Follow|
View Original Forum Topic
Current Tags for This Pattern
Caddis / sbs / Step-by-step tutorial / tutorial /
Andy's Edible Arrangement -- Caddis pupa attractor
tied by andy.larkin
Fly Type: Inverted Hook, Nymphs, Weighted,
Target Species: Steelhead, Pacific Salmon, Trout,
Recommended Region: Western Canada,
Hook: Hanak H450 (or 400) Size 10-12
Bead: 4mm Tungsten
Thread: UTC 140 Fl. White (I do tie these with Fl. Orange as well for hot spot collars..)
Body: Medium Amber V-Rib
Underbody: Medium Mirage opal tinsel/flashabou
Rib: White Senyo's Laser Dub, trimmed in dubbing loop
Thorax: Black CDC and SLF Spikey Squirrel Dubbing
Tying Instructions: A full step by step is also available at:
Place a size 10 Hanak Competition H450BL jig hook with 4mm slotted tungsten bead in your vice, starting the tying thread just behind the bead.
Make evenly spaced wraps towards the bend, and create a dubbing loop. Tie the loop down, allowing it to hang off the back and return your tying thread to the front of the fly. (line your last thread wrap covering the loop up with the eye of the hook).
Tie in a length of Medium AMBER Vinyl Ribbing, flat side down (be sure to leave about 1/4 inch behind the bead for the thorax.
Next, tie in some Mirrage tinsel. I do this by tying it in by the tip at the front, doing open wraps to the rear of the fly with the tinsel, then once again back to the front in even wraps to create a nice uniform underbody.
Wrap your V-rib body now forward, tying it off at the original tie in point (ensure the flat side stays down!)
Next, select a clump of white Senyo's Laser Dub. Using your fingers, pull the fibers to even them out.
Cut your clump of nicely evenly spaced dubbing into 1/3 to 1/2 inch lengths and place them in the dubbing loop. Space them evenly (and sparsely), then using your dubbing hook, twist the loop to create a dubbing rope.
Now, wrap the dubbing rope forward allowing it to sink into each of the segments of the vinyl ribbing and give it a brush out with your dubbing teaser to loosen any stray fibers.
Next (we're almost there..), select a CDC feather. I really like the Petit Jean select CDC feathers for this.. Cut about a 1 inch length of stem + fibers (from the middle of the feather) with long, even fibers and place itto the side.
Split your tying thread using a dress pin or dubbing hook.
Reduced: 62% of original size [ 1024 x 682 ] - Click to view full image
Place the 1 inch length of CDC feather in the split thread, as well as some SLF Spikey Squirrel Dubbing (Sparsely, allowing the fibers to be distributed evenly beneath it.).
Trim the stem leaving only the fibers in the split thread loop. Now pinch your thread beneath the dubbing in your left hand and give your bobbin a quick spin. Holding the thread at a 90 degree angle, perpendicular to the hook bend will allow the bobbin to spin much nicer and the thread to twist much better. Pinch the tying thread just above the tip of your bobbin and slide your fingers up. This will cause the rest of the turns you've created by spinning the bobbin to be forward, locking everything in place nicely.
Now, stroke the CDC fibers back on the tying thread so they are facing towards the bend of the hook and begin wrapping your collar/thorax up to the bead.
Tie off using a quick 3-4 turn whip finish, and give the thorax (and abdomen) a quick tease using a bodkin or soft dubbing teaser.
Presentation Tips: I fish this fly using spanish and czech nymphing technique depending on water conditions.
It fishes well using an upstream drift allowing the pattern to hang/swing once reaching the end of it's drift (which is usually when takes occur)
Other Flies Tied by andy.larkin
Members That Bookmarked This Fly Also Bookmarked...
|23 FTF Members Bookmarked This Pattern|